Just great place for everyone

How do you change modes in Down East Spa?

How do you change modes in Down East Spa?

SPA LIGHT – Your spa light is designed for safety and is located in the footwell of your spa. The on/off switch is located on the topside of the control panel.

How do I get my hot tub out of sleep mode?


How do I drain down my East Spa?

DRAINING YOUR LEGEND OR DOWN EAST SPA- The drain is located behind the front panel on the far right side. You can access the drain by unscrewing the black thumb screws and removing the corner panel. Grasp the drain cap, and pull the assembly out all the way.

What is EC mode on hot tub?

Economy mode heats the spa to the set temperature only during filter cycles. “Ec” or “Ecn” will appear solid when the temperature is not current and will alternate with the temperature.

What mode should hot tub be on?

Economy is a good setting for those who use the hot tub daily. The drop in temperature fluctuates during the year from minor or no temperature falls in the summer, to larger drops in the coldest part of winter.

Why does hot tub go into Eco mode?

Economy mode prevents your hot tub heater from activating between 7 am and 5 pm daily (or in older models prevents the heater from operating outside of primary filter cycles). If your hot tub is in this mode then you should expect to see water temperatures drop during the day (especially in winter).

What mode should I keep my hot tub on?

By default filter modes are 2 hours in the morning and 2 hours in the evening, the rest of the time the hot tub will use the insulation to keep the spa warm and retain heat. Economy is a good setting for those who use the hot tub daily.

How do I reset my hot tub control panel?

You can reset a hot tub control panel by switching it off, waiting for between 10 and 20 seconds and then switching it back on again. If the error signal continues on the control panel then you will need to consult your hot tub manual to see what the problem is.

How do I empty my spa water?

How to drain your Vortex spa or Swim Spa – YouTube

How do you drain a spa with a hose?

How to drain (empty) a spa by gravity if you do not have a submersible …

What setting should hot tub be on?


According to the US Consumer Product Safety Commission, the water temperature of a hot tub is best between 100°F and 102°F.

What temperature do you keep a hot tub when not in use?

As a general rule, a hot tub should be set between 98 and 104 degrees Farenheit even if not in use. For vacations lasting between 2 and 6 weeks, lower the temperature by 5 degrees. Beyond 6 weeks, consider powering down and draining.

What happens if you stay in a hot tub for 3 hours?

Since the water in a hot tub is a higher temperature than your normal internal temperature, staying in a hot tub too long can cause you to overheat and experience symptoms like light-headedness, dizziness, or nausea.

What setting do I leave my hot tub on?

your hot tub is designed to be left switched on constantly and works best when it is left on all the time. Your hot tub is at it’s most efficient if left to run 24/7.

How can I lower my electric bill in my hot tub?

5 Ways to Reduce your Hot Tub Energy Bill

  1. Get a Good Hot Tub Cover. The number one way to reduce your hot tub energy costs is to have the right hot tub cover for your environment.
  2. Lower the Thermostat.
  3. Set up a Wind Block.
  4. Lower the Thermostat when on Vacation.
  5. Heat at the Right Time.

What does SL mean on my hot tub?

SLEEP MODE (Sl): In this mode, your hot tub will heat the water up to the set temperature but only during the filtering cycles. You have the option to set each filter cycle to run anywhere from 30 minutes to 6 hours, with each cycle in increments of 30 mins.

Where is the reset button on hot tubs?

Most hot tubs are fitted with a reset button in the event of overheating or a power surge. The button is typically located on the side of the control box behind the hot tub’s removable panel on the front side. Similar to disposal reset buttons, simply press the small red button in to reset it.

How do I troubleshoot my hot tub control panel?

How To Fix A Hot Tub Control Panel (Troubleshooting)

  1. Start by resetting the spa controller.
  2. Check the controller for any condensation that may be present between the overlay and the display.
  3. Inspect the cables that run to the controller.
  4. Check the circuit board transformer to make sure there is power.

Can you empty spa water onto grass?

You shouldn’t drain your hot tub on your lawn. Spa water contains harmful chemicals like chlorine or bromine that will kill your grass and discolor your well-kept lawn. Instead, run your hose or drain well away from grass or vegetation and also away from the foundation supporting the hot tub.

How long can you leave a spa empty?

Keep in mind, we strongly recommend that you never leave your spa empty for a period of 2 weeks or more. Leaving your spa empty can cause damage to the pumps, heater element, and shell.

Can you drain a hot tub with a garden hose?

Locate the drainage valve of the hot tub. Connect the garden hose and run this to a drain. Open the valve to allow the water to drain out. Be aware that the process may take an hour or so – sometimes two.

Can I drain my hot tub on my lawn?

Is it cheaper to leave hot tub heater on all the time?

It’s cheaper!
One of the main reasons for keeping your hot tub on constantly is… cost! Once your hot tub is up to the desired temperature, it only requires a relatively small amount of electricity to keep the water at that temperature.

Is it cheaper to leave a hot tub on all the time?

Yes, you should leave your hot tub on all of the time. Hot tubs are designed to always be switched on and it’s more economical to keep the water hot than it is to heat it up from cold each time you want to use it.

What is the most economical setting for hot tub?

The easiest way to save money on your hot tub is to turn the temperature down a few degrees. Each degree will save you approx. 10% on your hot tub energy bill.