Is Lysaght the same as COLORBOND?
LYSAGHT® Roofing & Walling is manufactured from COLORBOND® and ZINCALUME® steel. LYSAGHT Roof Sheeting and Wall Cladding come in a range of profiles to suit any architectural style.
What is Lysaght Trimdek?
LYSAGHT TRIMDEK® is a versatile roof and wall cladding featuring bold, trapezoidal ribs and subtle fluting in the pans. Ideal for commercial, industrial and residential buildings. It can be used with the LYSAGHT TRIM-KLIP® end and expansion joint system.
What is the minimum pitch for a custom orb roof?
5 degrees
minimum roof pitch
a special anti-capillary forming in the side lap allow you to use custom orb (or custom blue orb used on curved surfaces) for roof pitches as low as 5 degrees (1 in 12).
What is Trimdek roofing?
Description. LYSAGHT TRIMDEK® is a subtle square-fluted steel cladding, available in long lengths, so on most jobs you can have one sheet from ridge to gutter without end laps. It is made of high strength steel and despite its lightness, provides excellent spanning capacity and remarkable recovery after deformation.
Does BlueScope own Lysaght?
Lysaght is a division of BlueScope in Australia and has been supplying steel building products for residential and commercial projects across Australia for over 150 years.
Is colorbond Matt more expensive?
Yes, matt products in the Colorbond range tend to be more expensive. However, the effect is well worth the few extra dollars per square metre. A matte finish like the one pictured above helps to keep the colour bright over the years as well as creating a softer, more subtle immediate look.
What is the minimum fall for Trimdek roofing?
TRIMDEK Roof and Walling Sheets are suitable for use on a roof pitch of 2° or greater.
How do you screw down Trimdek?
Fastening Sheets to Supports
To maximise water tightness, always place roof screws through the crests. For walling, you may use either crest or valley fixing. Always drive the screws perpendicular to the sheeting and in the centre of the corrugation or rib. Don’t place fasteners less than 25 mm from the ends of sheets.
What is the lowest pitch you can put on a metal roof?
The minimum slope for lapped, non-soldered seam metal roofs without applied lap sealant shall be three units vertical in 12 units horizontal (25-percent slope). The minimum slope for lapped, non-soldered seam metal roofs with applied lap sealant shall be one-half unit vertical in 12 units horizontal (4-percent slope).
What is the best pitch for a skillion roof?
Skillion roofs should have a primary roof pitch of between 10 and 15 degrees and secondary roof pitch of not less than 5 degrees; Homes with a roof pitch outside of these requirements will bE considered on architectural merit.
Is LYSAGHT Australian made?
Proudly made in Australia since 1921, Lysaght steel building products have shaped the nation. From quintessential corrugated roofing to large commercial & industrial projects, Lysaght has been at the forefront of the Australian building industry throughout its proud heritage.
Is BlueScope Steel made in China?
BlueScope Steel
Our operations in China comprise a metallic coating and painting facility at Suzhou, three world class building systems manufacturing facilities, 32 sales and marketing offices and approximately 1,200 employees.
What is the most popular COLORBOND roof colour?
What are the Most Popular Colorbond® Roof Colours?
- Basalt.
- Cove.
- Dune.
- Evening Haze.
- Gully.
- Ironstone.
- Jasper.
- Mangrove.
How long should a COLORBOND roof last?
up to 70 years
Lifespan – Colorbond roofs can have a life expectancy of up to 70 years whereas tile roofs are easily damaged and prone to cracking under typical Australian weather extremes.
What is a 1 40 fall on a flat roof?
In real terms, a 1:40 fall equates to 25mm per metre run of roof. Hence a ten metre run requires 250mm of fall from high to low point.
Can you overlap metal roofing lengthwise?
Yes, you can install metal roofing by overlapping it lengthwise. Metal roofs on your house need to be installed with care to avoid leaks.
How far apart do you screw metal roofing?
Lap screws are spaced 12” to 18” on center. The panel screws are spaced out so that every third corrugation has a screw including both sides of the panel sidelap.
Does metal roofing require an underlayment?
The short answer is yes, your metal roof does need underlayment . But like most things in life, it’s not quite that simple. At Western States Metal Roofing , we have specialized in manufacturing metal roofing for over 20 years.
Can you walk on a metal roof with purlins?
All metal roofing systems, especially steel roofing, can be walked on. Proper fall protection is always important when walking on any roof – never walk on a wet roof or one that has dew on it. Never walk on metal roofing panels before they are properly fastened down.
What are the disadvantages of a skillion roof?
Disadvantages of Skillion Roof
Skillion roof might result in the low height of the ceiling if the pitch is way too steep. Skillion roofs sustain vandalism easily in hurricane force winds. The gradients of these roofs are way too compressed if we compare them with the typical roofs shaping like gable and hip.
How far can a skillion roof span?
Skillion roofs have one single flat surface that slopes to one side. They are also referred to as a mono-pitch, and the roof line can be designed up to a 12m span.
What was Lysaght originally used for?
It all started back in 1857 when a 25-year-old Irishman by the name of John Lysaght saw potential in corrugated iron sheeting, and started exporting it to Australia under the trademark “ORB”. Lysaght corrugated iron helped build the nation’s domestic and industrial landscape.
Is COLORBOND made in China?
The Suzhou facility, located 80 km west of Shanghai, is designed to supply China’s booming building and construction markets. The plant can produce the full BlueScope Steel range of coated products, including the premium brands Clean COLORBOND® steel and ZINCALUME® steel.
Is COLORBOND owned by BlueScope?
BlueScope’s portfolio of highly regarded brands includes COLORBOND® steel, COLORSTEEL®, ZINCALUME® steel, GALVABOND® steel, GALVASPAN® steel, LYSAGHT® steel building products, BlueScope Zacs®, and SuperDyma®. An additional range of products meets specific regional needs in Asia.
Are dark Colorbond roofs hotter?
From our experience of installing Colorbond metal roof for all around NSW, light coloured roof does indeed make home a bit cooler than dark coloured roof.