How do I adjust my Arlec sensor light?
To increase time, turn the knob clockwise. To decrease, turn knob anti- clockwise. The “Lux” control adjusts at what level of light the unit starts sensing at dusk. This control can be also used for testing the unit during daylight hours.
How do I use my Arlec sensor light?
Turn anti-clockwise to increase ON-time – ideal setting is about 2 o’clock position (approximately 2 minutes). Whilst there is movement within range of the unit, the light will remain ON. When no further movement is detected, the light will switch OFF after the pre-set time has elapsed.
How do I change my sensor light settings?
Use the sensitivity control to adjust the sensor to light up more or less area as needed. Check your adjustment by walking in circles beneath your motion sensor. Again.
How do I turn my sensor light on?
This is done by turning the light switch OFF – ON – OFF – ON in quick succession. The light will then remain ON and will not go OFF until you manually turn it OFF at the switch. When you’re ready to use the sensor again, simply turn the light switch OFF and leave it there for at least a minute.
Why does my security light stay on all the time?
What Causes my Light to Stay On? Several things can cause your motion detector to stay on, including age, storm damage, a power surge, improper installation, and improper settings. A few issues are easy to correct without professional help.
Why won’t my motion sensor light go off?
The Problem
Some movement sensors have a built-in override functionality. If the override function is engaged, the sensor light will stay on until the override function is disengaged. This override function is often engaged accidentally which causes confusion and the mistaken belief that the sensor is faulty!
What is Lux adjustment?
PIR adjustment
LUX is the setting for the ambient light level below which the PIR detector will be activated. Once installed, connected and angle adjusted as required, set all 3 of the above settings to the minimum level (anti-clockwise).
How do you keep a sensor light from staying on?
The best way to reset a motion sensor light is to turn it off and back on again for a period of 30 seconds or longer. A homeowner can also turn the power to it off at the breaker, in order to ensure it has time to reset itself. If that doesn’t work, the sensor itself or the bulb may be to blame.
Why does my sensor light keep going on and off?
A motion light switching on and off could be due to many reasons. Incompatible LED bulbs are common, but also, the sensor may be faulty or damaged power bumps, or even spiders. Try changing the bulb, resetting the sensitivity, or replacing the sensor if nothing else works.
How do I get my motion sensor light to work?
Why is my sensor light not working?
Wipe the sensor with a clean, soft cloth—something that doesn’t scratch glass and plastic surfaces. Check and/or change the bulb. If the sensor is clean and clear, but the problem persists, you might examine or change the bulbs in your motion light, since they last a while, but will wear out over time.
Why will my sensor light not go off?
Why won’t my motion sensor lights turn off?
If the motion sensor was triggered during that brief period where the switch was off, your light fixture could possibly be stuck in the auto-on mode. To fix this, cut power to the motion light altogether for a full 10 seconds, and then restore power.
Why does my sensor light stay on all the time?
How do you adjust an outdoor motion sensor light?
How to Install Outdoor Motion Lights – YouTube
What are the 3 settings on a sensor light?
There are 3 settings on a motion sensor light: sensitivity, timer, and lux. These 3 settings determine how sensitive the light is to movement, how long the light will stay on after detecting movement, and what level of darkness the light will turn on in.
What are the 3 dials on a security light?
The lens should be replaced with a suitable replacement. LIGHT SETTINGS The Flood Light is fitted with three setting dials (SENS – SENSITIVITY; TIME; LUX – LIGHT LEVEL).
How do you stop motion sensor lights from turning off?
One of the quick tricks you can try is to quickly turn the motion sensor ON, OFF, ON to override the motion detection and make the light stay on. To go back to motion detection mode, turn the motion sensor off, wait for about 10 seconds, and then turn it on again.
Why won’t my motion light come on?
The Light Won’t Come On
Turn off the circuit breaker that controls the light circuit and leave it off for 30 minutes. Turn on the breaker and see if the light comes on. If it does, adjust the sensor range and sensitivity as needed. If the light doesn’t come on when you turn the breaker back on, try replacing the bulb.
How do you reset motion sensor lights?
Turn the light switch on and off rapidly approximately four times. The light will eventually stay on continuously. Once the light is on, turn the switch off, wait five seconds and turn it back on again. The light should stay off and the sensor should be reset.
Why are my sensor lights staying on?
What Causes my Light to Stay On? Several things can cause your motion detector to stay on, including age, storm damage, a power surge, improper installation, and improper settings.
How do you turn off motion sensor lights?
Turn your light switch on and off quickly, hitting each position four times. When the light comes on, turn the switch to the off position and wait five to seven seconds before turning it on again. The light should remain off and the motion detection unit should be reset.
Why is my motion light staying on all the time?
Why does my motion sensor light not turn off?
If your duration setting is too long, it may seem like your motion light never turns off. Stuck in Auto-On – Many lights have an auto setting that causes them to stay on all the time. It’s possible that you’ve triggered this mode without even realizing it. Malfunctions can also cause lights to get stuck in this mode.
How do you stop a motion sensor light from turning off?
The easiest way to stop motion detector lights from turning off is to… turn them off and quickly turn them on again. Most modern motion sensor lights are designed or programmed to interpret this as an override command. In older motion sensor lights, it simply resets the timer.